Best USB to Serial (UART) Adapters: 13 FTDI, CP2102, CH340, PL2303 and Isolated USB to TTL Picks Compared (Buying Guide)

⚠️ Affiliate Disclosure: This post contains Amazon affiliate links. If you purchase through our links, we may earn a small commission at no extra cost to you. Every product below was checked against its live Amazon listing before publishing. Prices change often, so we don’t list them here. Tap any Buy Here button to see the current price on Amazon.
Ultimate Buying Guide

🔌 Best USB to Serial (UART) Adapters

13 FTDI, CP2102, CH340 and PL2303 USB to TTL adapters and cables for flashing ESP32 and ESP8266 boards, programming Arduino Pro Minis, reading Raspberry Pi consoles and unbricking routers.

✅ 13 Adapters Reviewed✅ FTDI, CP2102, CH340, PL2303✅ Isolated and 1.8V Picks✅ Honest Pros and Cons

A USB to serial (UART) adapter, often sold as a USB to TTL converter, turns a USB port into a pair of TX and RX logic-level lines your microcontroller understands. It is the tool you reach for when a board has no USB port of its own (Arduino Pro Mini, ESP-01, bare ESP32 modules), when you need a Raspberry Pi or router boot console, or when you want a second serial port for debug logs while the main USB is busy. Most adapters also break out DTR or RTS so the IDE can reset the target automatically before uploading.

If UART itself is new to you, start with our UART communication explainer, and see our CP2102 module guide for a hands-on example of programming an Arduino Pro Mini. This guide compares the adapters worth buying, from genuine FTDI boards to cheap CH340 multipacks.

💡 Reality check before you buy: These are TTL (logic-level) adapters, not RS232. Never connect them to a PC-style DB9 RS232 port, which swings to plus and minus 12V. Match the logic voltage to your target: most ESP32, ESP8266, STM32 and Raspberry Pi pins are 3.3V only, so set the jumper to 3.3V before wiring, and use a 1.8V capable adapter for many router and phone SoCs. Remember to cross the lines (adapter TX to target RX) and share ground. The VCC pin on most small adapters can only supply a little current, so power hungry boards such as an ESP32 with Wi-Fi active are better powered separately. Cheap FT232RL boards are sometimes clone chips, and one HiLetgo listing here states its chip is not genuine FTDI, so buy a branded genuine FTDI adapter if you need guaranteed driver support. Older PL2303 chips can be refused by newer Windows drivers; the PL2303TA picks below use the newer chip.
Table of Contents
  1. Quick Comparison: All 13 USB to UART Adapters
  2. How to Choose a USB to Serial Adapter
  3. Detailed Reviews: All 13 Picks
  4. Which One for Which Job
  5. FTDI vs CP210x vs CH340 vs PL2303 Chips
  6. Frequently Asked Questions
  7. Final Verdict: Best USB to Serial (UART) Adapters

🔌 Quick Comparison: All 13 USB to UART Adapters

ProductChipLogic Levels (per listing)FormRatingBest ForBuy
🥇 DSD TECH SH-U09CFTDI FT232RL3.3V / 5V (jumper)Board, 6 pin⭐ 4.6 (2,160)Best OverallBuy Here →
💰 HiLetgo CP2102Silicon Labs CP21023.3V and 5V pinsBoard, USB-A⭐ 4.5 (951)Best BudgetBuy Here →
🎚️ DSD TECH SH-U09C5FTDI FT232RNL5V / 3.3V / 2.5V / 1.8VCased board + 6 pin cable⭐ 4.8 (970)Best Multi-VoltageBuy Here →
🧩 HiLetgo FT232RL MiniFT232RL (not genuine FTDI, per listing)3.3V / 5.5VMini board, 6 pin⭐ 4.4 (1,232)Best Pro Mini HeaderBuy Here →
🛠️ DSD TECH SH-U09C2FTDI FT232RL5V / 3.3V / 1.8V (jumper)Cased board⭐ 4.8 (945)Best for Router UnbrickingBuy Here →
📦 HiLetgo CH340 (5 pack)WCH CH340Not stated in bulletsUSB stick boards⭐ 4.4 (246)Best MultipackBuy Here →
🛡️ DSD TECH SH-U09C3 IsolatedFTDI FT232RL + ADI iCoupler3.3V / 5V (jumper)Cased isolated board⭐ 4.6 (140)Best IsolatedBuy Here →
🔴 SparkFun FTDI Basic 5VFTDI FT232RL5V default (3.3V by jumper)Breakout, Mini-B⭐ 4.6 (132)Best Arduino BreakoutBuy Here →
🧷 SparkFun Serial Basic CH340GWCH CH340G3.3V default (5V by jumper)Breakout, 6 pin⭐ 4.6 (57)Best Branded CH340Buy Here →
🏭 Waveshare Industrial FT232RNLFTDI FT232RNLNot stated in bulletsIndustrial cased converter⭐ 4.5 (119)Best IndustrialBuy Here →
🍓 DTECH 3.3V TTL CableProlific PL2303TA3.3V signals, 5V VCC wire6 ft cable, 4 pin socket⭐ 4.3 (279)Best Pi Console CableBuy Here →
🔋 DSD TECH SH-U09B3 USB-CSilicon Labs CP2102N5V VCC pin (logic not stated)Board, USB-C⭐ 4.3 (78)Best USB-CBuy Here →
🧵 PL2303TA Console Cable (3 pack)Prolific PL2303TA5V or 3.3V power output4 wire cable x3⭐ 3.9 (394)Best Cheap CablesBuy Here →

Specs, ratings and review counts are taken from the live Amazon listings at the time of writing and can change. Always confirm details on the product page.

🔍 How to Choose a USB to Serial Adapter

⚡

Logic Voltage

Check your target first. A 3.3V and 5V jumper covers Arduino, ESP and Pi boards. Router, TV box and phone debugging often needs 1.8V, which only the DSD TECH SH-U09C2 and SH-U09C5 list here.

🧠

Chip and Drivers

Genuine FTDI and Silicon Labs CP210x chips have the most mature drivers. CH340 is cheap and fine for hobby work but may need a driver on older Windows and macOS. PL2303 is common in console cables.

🔁

Reset and Flow Control Pins

DTR or RTS lets the Arduino IDE and esptool reset the target automatically. CTS and RTS add hardware flow control. A plain 4 wire cable only gives TX, RX, power and ground.

🛡️

Isolation and Protection

Working on mains powered gear, motor drivers or industrial kit? An isolated adapter like the SH-U09C3 protects your laptop from ground loops and surges.

🔗

Board or Cable

Small boards with header pins suit the bench. Long cables with female jumpers are easier for Raspberry Pi GPIO consoles and devices inside enclosures.

🏆 Detailed Reviews: All 13 Picks

🥇 BEST OVERALL

DSD TECH SH-U09C USB to TTL Serial Adapter (FTDI FT232RL)

⭐ 4.6/5 · 2,160 ratings · Genuine FTDI, 3.3V and 5V jumper
FT232RL
FTDI CHIP
900K
MAX BAUD (LISTED)
3.3V/5V
JUMPER SELECT
2,160
AMAZON RATINGS
Buy on Amazon →
DSD TECH SH-U09C USB to TTL serial adapter with FTDI FT232RL chip

With 2,160 ratings the SH-U09C is the most-reviewed TTL adapter we found and the safest default. Per the listing it uses the FTDI FT232RL chip, reaches up to 900K baud, has LED indicators for TX, RX and power, and breaks out CTS, RTS, RXD, TXD, GND and VCC with a jumper to switch the VCC output between 3.3V and 5V. It works with Windows 11, 10 and 7 and macOS. It averages 4.6 stars.

✅ Pros
  • Genuine FTDI chip with mature drivers
  • TX, RX and power LEDs help debugging
  • Huge user base
❌ Cons
  • RTS rather than DTR, so Arduino auto-reset needs care
  • No 1.8V option
🎯 Verdict: The adapter to keep in your toolbox for ESP flashing, GPS modules and serial debugging.

👉 Check Price on Amazon →

💰 BEST BUDGET PICK

HiLetgo CP2102 USB 2.0 to TTL Module

⭐ 4.5/5 · 951 ratings · Plugs straight into a USB-A port
CP2102
SILABS CHIP
1.5 Mbps
MAX BAUD (LISTED)
5 PIN
3.3V RST TX RX GND 5V
951
AMAZON RATINGS
Buy on Amazon →
HiLetgo CP2102 USB to TTL serial converter module

The HiLetgo CP2102 is the classic stick-style adapter that plugs directly into a USB-A port with no cable. Per the listing it uses the CP2102 chip, supports 300 bps to 1.5 Mbps, and has a 5 pin header with 3.3V, RST, TXD, RXD, GND and 5V, plus jumper wires in the box. Drivers are listed for Windows, macOS and Linux. It averages 4.5 stars from 951 ratings.

✅ Pros
  • Both 3.3V and 5V supply pins
  • Tiny, no cable to lose
  • Fast 1.5 Mbps ceiling
❌ Cons
  • No CTS or DTR on the header
  • Blocks neighbouring USB ports on some laptops
🎯 Verdict: The best value everyday adapter for ESP8266, ESP32 and Arduino serial work.

👉 Check Price on Amazon →

🎚️ BEST MULTI-VOLTAGE · ⭐ 4.8/5

3. DSD TECH SH-U09C5 USB to TTL UART Converter Cable

Four TTL levels, full modem pins · 970 ratings
Buy Here →
DSD TECH SH-U09C5 USB to TTL UART converter with FTDI chip and 6 pin cable

The SH-U09C5 is the most flexible adapter in this guide. Per the listing it supports 5V, 3.3V, 2.5V and 1.8V TTL levels, uses an original FTDI FT232RNL chip, and comes in a clear protective case. Besides TX, RX, RTS, CTS, VCC and GND it also brings out DSR, RI, DCD, DTR and RESET, and a 6 pin cable is included. It holds a 4.8 star average from 970 ratings.

✅ Pros: 1.8V and 2.5V for router and SoC consoles
❌ Cons: Overkill if you only flash ESP boards
🎯 Verdict: The one adapter that covers almost every logic level you will meet.
🧩 BEST CHEAP PRO MINI ADAPTER · ⭐ 4.4/5

4. HiLetgo FT232RL Mini USB to TTL Serial Converter

DTR pin, 500mA resettable fuse · 1,232 ratings
Buy Here →
HiLetgo FT232RL mini USB to TTL serial converter adapter module

This tiny board uses the DTR, RXD, TX, VCC, CTS, GND pinout that matches the Arduino Pro Mini programming header, so DTR can trigger the auto-reset. Per the listing it switches between 3.3V and 5.5V, has RX and TX indicators and a 500mA self-restoring fuse. The listing is upfront that the chip is not a genuine FTDI part and that Windows 8 is not supported, and its bullets also mention a 3 pack USB-C variant, so check the selected option. It averages 4.4 stars from 1,232 ratings.

✅ Pros: Pro Mini friendly DTR pinout with fuse protection
❌ Cons: Clone FT232RL chip, driver support can vary
🎯 Verdict: A cheap, popular Pro Mini programmer if you accept a clone chip.
🛠️ BEST FOR ROUTERS AND 1.8V · ⭐ 4.8/5

5. DSD TECH SH-U09C2 USB to TTL Adapter (FTDI FT232RL)

5V, 3.3V and 1.8V by jumper · 945 ratings
Buy Here →
DSD TECH SH-U09C2 USB to TTL adapter with FTDI FT232RL IC

The SH-U09C2 adds a 1.8V setting to the familiar FTDI design. Per the listing it uses an original FTDI FT232RL, switches between 5V, 3.3V and 1.8V logic by jumper, comes in a transparent protective case, and is aimed at EEPROM and vendor ID rewrites, unbricking routers, programming ESP8266 modules, GPS modules and set top box consoles. It averages 4.8 stars from 945 ratings.

✅ Pros: 1.8V logic in a simple jumper
❌ Cons: No 2.5V option like the SH-U09C5
🎯 Verdict: Ideal for router, TV box and embedded Linux console work.
📦 BEST MULTIPACK · ⭐ 4.4/5

6. HiLetgo 5pcs USB to TTL CH340 Module

Five adapters, STC downloader · 246 ratings
Buy Here →
HiLetgo CH340 USB to TTL module 5 pack

Need an adapter for every project box or a classroom? This 5 pack of CH340 USB to TTL modules is the cheapest way to get there. The listing describes them as USB to TTL modules and STC microcontroller downloaders. The bullets are thin and do not spell out the logic level jumper, so check the board markings and set 3.3V before wiring to an ESP32 or Pi. It averages 4.4 stars from 246 ratings.

✅ Pros: Five adapters for the price of one branded board
❌ Cons: Very sparse listing details
🎯 Verdict: Great for labs, classrooms and leaving one adapter wired into each project.
🛡️ BEST ISOLATED ADAPTER · ⭐ 4.6/5

7. DSD TECH SH-U09C3 Isolated USB to TTL Adapter

ADI iCoupler isolation, FTDI chip · 140 ratings
Buy Here →
DSD TECH SH-U09C3 isolated USB to TTL adapter with FT232RL

When the target shares ground with mains powered equipment, motor drivers or industrial gear, an isolated adapter protects your laptop. Per the listing the SH-U09C3 uses ADI iCoupler signal isolation to shield the PC’s USB port from external short circuits and shocks, with an FTDI FT232RL chip, TX, RX and power LEDs, a protective case and a 3.3V or 5V jumper. It averages 4.6 stars from 140 ratings.

✅ Pros: Isolation for noisy or high energy targets
❌ Cons: Bigger than a basic adapter
🎯 Verdict: The safe choice for inverters, motor controllers, PLCs and anything near mains.
🔴 BEST ARDUINO-STYLE BREAKOUT · ⭐ 4.6/5

8. SparkFun FTDI Basic Breakout 5V

FTDI cable pinout, DTR auto-reset · 132 ratings
Buy Here →
SparkFun FTDI Basic Breakout 5V USB to serial board

SparkFun’s FTDI Basic is the board many Arduino Pro Mini tutorials are written around. Per the listing it breaks out the FTDI FT232RL with a pinout that matches the official FTDI cable, brings out DTR instead of RTS so the Arduino resets automatically when a sketch uploads, and labels BLK and GRN pins to help alignment. It ships set to 5V, with a jumper on the back you can change to 3.3V. It uses a USB Mini-B connector and averages 4.6 stars from 132 ratings.

✅ Pros: Plug-and-play Arduino auto-reset
❌ Cons: Mini-B cable is getting rare
🎯 Verdict: The reference choice for Pro Mini and LilyPad style boards.
🧷 BEST BRANDED CH340 · ⭐ 4.6/5

9. SparkFun Serial Basic Breakout CH340G

Arduino pinout, 3.3V default · 57 ratings
Buy Here →
SparkFun Serial Basic Breakout CH340G USB to serial board

The Serial Basic is SparkFun’s lower cost alternative using the CH340G from WCH. Per the listing it works with 5V and 3.3V systems, should auto install on most operating systems without extra drivers, and uses the DTR, RX, TX, VCC, CTS, GND pinout. It ships with 3.3V output and signals by default, with a jumper to change to 5V. It averages 4.6 stars from 57 ratings.

✅ Pros: Safe 3.3V default for ESP and Pi boards
❌ Cons: Fewer reviews than the big sellers
🎯 Verdict: A well-documented CH340 board from a brand with good tutorials.
🏭 BEST INDUSTRIAL CONVERTER · ⭐ 4.5/5

10. Waveshare Industrial USB to TTL Converter (FT232RNL)

Multi protection circuits · 119 ratings
Buy Here →
Waveshare industrial USB to TTL converter with FT232RNL

Waveshare’s industrial converter wraps an original FTDI FT232RNL in a rugged design with multiple protection circuits. Per the listing it is compatible with Windows 7 to 11, macOS, Linux, Android and WinCE, and has status indicators for programming and debugging. The bullets do not list the logic level selection, so check Waveshare’s wiki for the jumper settings before use. It averages 4.5 stars from 119 ratings.

✅ Pros: Protected design for field and production use
❌ Cons: Listing light on logic level details
🎯 Verdict: Good for production lines, field service kits and long-term installs.
🍓 BEST PI CONSOLE CABLE · ⭐ 4.3/5

11. DTECH USB to TTL Serial 3.3V Adapter Cable (PL2303TA)

6 ft, 4 pin 0.1 inch female socket · 279 ratings
Buy Here →
DTECH USB to TTL serial 3.3V cable with PL2303 chip

A cable is often easier than a board when the target sits inside an enclosure. Per the listing this 6 ft DTECH cable houses a genuine PL2303TA chip inside the USB-A plug and ends in a 4 pin 0.1 inch female socket carrying Tx, Rx, VCC (5V) and GND for 3.3V logic UART devices. The EEPROM is configurable, including UART signal inversion. It averages 4.3 stars from 279 ratings.

✅ Pros: Long reach, nothing to break on the bench
❌ Cons: No reset or flow control lines
🎯 Verdict: A tidy choice for Raspberry Pi serial consoles and devices in cases.
🔋 BEST USB-C ADAPTER · ⭐ 4.3/5

12. DSD TECH SH-U09B3 USB Type C to TTL Serial Adapter (CP2102N)

CP2102N up to 3 Mbps · 78 ratings
Buy Here →
DSD TECH SH-U09B3 USB Type C to TTL serial adapter with CP2102N

If your laptop only has USB-C ports, the SH-U09B3 saves you a dongle. Per the listing it uses the upgraded Silicon Labs CP2102N, which the listing says reaches 3 Mbps, and breaks out VCC (5V), GND, TX, RX, CTS and RTS. The listing does not state the logic voltage, so confirm it before connecting a 3.3V only board. It averages 4.3 stars from 78 ratings.

✅ Pros: Native USB-C and a fast CP2102N
❌ Cons: Logic level not spelled out in the listing
🎯 Verdict: The pick for USB-C only MacBooks and ultrabooks.
🧵 BEST CHEAP CONSOLE CABLES · ⭐ 3.9/5

13. PL2303TA USB to TTL Serial Debug Console Cable (3 Pack)

Red 5V, black GND, green TX, white RX · 394 ratings
Buy Here →
PL2303TA USB to TTL serial debug console cable 3 pack for Raspberry Pi

This 3 pack of classic four wire console cables uses the PL2303TA chip. Per the listing the wires are red 5V, black ground, green TX and white RX, the cable can be configured for 5V or 3.3V power output, and it is meant for microcontrollers, Raspberry Pi and Wi-Fi router serial consoles. Its 3.9 star average from 394 ratings is the lowest here, so treat these as spares rather than your main tool.

✅ Pros: Three cables, color coded wires
❌ Cons: Lowest rating in this guide
🎯 Verdict: Cheap spares to leave connected to headless Pis and routers.

🧭 Which One for Which Job

📶

Flashing ESP32 and ESP8266 modules

HiLetgo CP2102 or DSD TECH SH-U09C at 3.3V. For more boards, see our ESP32-S3 development boards guide.

🔵

Arduino Pro Mini and LilyPad

SparkFun FTDI Basic for DTR auto-reset, or the budget HiLetgo FT232RL Mini. See our Arduino Pro Mini guide.

🍓

Raspberry Pi serial console

DTECH 3.3V cable or the PL2303TA 3 pack on GPIO 14 and 15.

📡

Router, TV box and SoC consoles

DSD TECH SH-U09C2 or SH-U09C5 for 1.8V logic.

⚙️

Motor drivers, inverters and PLCs

DSD TECH SH-U09C3 isolated adapter, or the Waveshare Industrial converter.

🏫

Classrooms and project boxes

HiLetgo CH340 5 pack or SparkFun Serial Basic for a 3.3V default.

⚙️ FTDI vs CP210x vs CH340 vs PL2303 Chips

FeatureFTDI FT232R / RNLSilicon Labs CP2102 / CP2102NWCH CH340 / CH340GProlific PL2303TA
Picks in this guideSH-U09C, SH-U09C2, SH-U09C5, SH-U09C3, SparkFun FTDI Basic, WaveshareHiLetgo CP2102, SH-U09B3HiLetgo CH340, SparkFun Serial BasicDTECH cable, PL2303TA 3 pack
Driver maturityExcellentExcellentGood (driver may be needed on older Windows and macOS)Good on the newer TA chip
Clone riskCommon on cheap unbranded boardsLowVery low (cheap genuine chip)Older chips widely cloned
Modem pins on typical boardsFull set (DTR, RTS, CTS and more)RTS, CTS, sometimes DTRDTR, CTS on SparkFunUsually TX and RX only
1.8V logic options hereYes (SH-U09C2, SH-U09C5)NoNoNo
Isolated option hereYes (SH-U09C3)NoNoNo
Typical costHigherMidLowestLow
Best forProfessional debug and odd voltagesEveryday ESP and Arduino workBudget and multipacksConsole cables

Chip notes are general guidance. Features of each pick are taken from its Amazon listing.

❓ Frequently Asked Questions

Is a USB to TTL adapter the same as a USB to RS232 adapter?

No. TTL adapters use 0V and 3.3V or 5V logic levels that connect directly to microcontroller pins. RS232 uses plus and minus voltages of up to about 12V on a DB9 port and will damage a microcontroller pin. For RS485 field buses, see our RS485 modules guide.

Which logic voltage should I set?

Use 3.3V for ESP32, ESP8266, STM32, RP2040 and Raspberry Pi, 5V for classic 5V Arduino boards such as the 5V Pro Mini, and 1.8V for many router and phone SoCs. When unsure, measure the target’s TX pin with a multimeter while it boots.

Why does my ESP32 not enter download mode?

esptool uses the DTR and RTS lines to pulse EN and GPIO0. Adapters without both lines need you to hold the BOOT button and tap EN (reset) manually. Also check that TX goes to RX, ground is shared and the board has enough power.

Do I need drivers?

Linux and recent macOS and Windows versions include drivers for most FTDI, CP210x and CH340 chips. If the port does not appear, install the driver from the chip maker (FTDI, Silicon Labs, WCH or Prolific) rather than from a random download site.

Can a USB to serial adapter debug an ARM chip?

Only through a serial bootloader or a printf style log. For breakpoints and stepping you need an SWD or JTAG probe, covered in our JTAG and SWD debuggers guide, and for decoding UART, I2C and SPI traffic a logic analyzer is the better tool.

🏁 Final Verdict: Best USB to Serial (UART) Adapters

Our picks for the most common setups:

🥇 Best Overall: DSD TECH SH-U09C (FTDI FT232RL)
Buy Here →
💰 Best Budget: HiLetgo CP2102 USB to TTL Module
Buy Here →
🎚️ Best Multi-Voltage: DSD TECH SH-U09C5 (5V to 1.8V)
Buy Here →
🛡️ Best Isolated: DSD TECH SH-U09C3 Isolated Adapter
Buy Here →
🔴 Best for Arduino Pro Mini: SparkFun FTDI Basic Breakout 5V
Buy Here →
🔋 Best USB-C: DSD TECH SH-U09B3 (CP2102N)
Buy Here →

For most makers the DSD TECH SH-U09C is the adapter to buy once and keep, while the HiLetgo CP2102 is the best low cost option for ESP and Arduino work. Choose the SH-U09C5 or SH-U09C2 when you need 1.8V, the isolated SH-U09C3 for high energy targets, and a SparkFun board for Pro Mini style auto-reset. For more debugging and programming tools, see our guides to JTAG and SWD debuggers, logic analyzers, EEPROM and BIOS programmers, USB to CAN adapters, RS485 modules and our UART communication tutorial.

💬 Which USB to serial adapter lives in your toolbox, and have you been caught out by a clone chip or a 5V jumper on a 3.3V board? Share your story in the comments below.

All Amazon links above use our affiliate tag (microlab05-20). Purchasing through them supports microcontrollerslab.com at no extra cost to you. Prices and availability change frequently, so always confirm the current price on Amazon before buying.

Leave a Comment