ATMEGA328P Microcontroller

ATmega328P is one of the high performances AVR technology microcontroller with a large number of pins and features. It is designed by 8-bit CMOS technology and RSIC CPU which enhance its performance and its power efficiency get improved by auto sleeps and internal temperature sensor. This ATmega328P IC comes with internal protections and multiple programming methods which helps the engineers to priorities this controller for different situations. The IC allows multiple modern era communications methods for other modules and microcontrollers itself, which is why the microcontroller ATmega328P usage has been increasing every day.

Pinout Diagram ATmega328P

In this section, we will see the usage of each pin and pin diagram details for this 28 pin microcontroller. This picture shows the pinout diagram:

Othe alternative options for ATMEL microcontrollers are ATtiny45, ATtiny88, ATtiny85

Pin configuration Details

DIGITAL INPUT/OUTPUT PINS 

This microcontroller has three digital ports (B, C, D) such as PORTB, PORTC, and PORTD. All these pins can be used as digital input/output. On top of that, each port can be used for other purposes. To use them as output/input or for any other function it should be defined first otherwise there won’t be any default function by all I/O pins. Digital I/O pins of the controller are:

• PB0 – GPIO14
• PB1 – GPIO15
• PB2 – GPIO16
• PB3 – GPIO17
• PB4 – GPIO18
• PB5 – GPIO19
• PB6 – GPIO9
• PB7 – GPIO10
• PC0 – GPIO23
• PC1 – GPIO24
• PC2 – GPIO25
• PC3 – GPIO26
• PC4 – GPIO27
• PC5 – GPIO28
• PC6 – GPIO1
• PD0 – GPIO2
• PD1 – GPIO3
• PD2 – GPIO4
• PD3 – GPIO5
• PD4 – GPIO6
• PD5 – GPIO11
• PD6 – GPIO12
• PD7 – GPIO13

INTERRUPT PINS

Most of the electrical functions required an interrupt system to operate like AC dimmer, etc. ATmega328P gives the support of 2 interrupts within the controller which can be used to get the attention of the CPU at any instant. Interrupt pins of ATmega328P are given below:

• IN0 – GPIO4
• IN1 – GPIO5

ATmega328P  UART Communication Module 

Although there are multiple kinds of communication systems within the devices and modules but the most common one is USART. It is one of the simplest and easiest method for implement and understanding by most of the developers and systems. In this method, two wires used to send and receive the data. The USART pins of microcontroller ATmega328P are:

• RX – GPIO2
• TX – GPIO3

The data can be sent by specified the sending rate within the controllers but it can also use the external clock pin to keep the data sync.

• XCK – GPIO6

USART/UART communication system ca be used to program the microcontroller.

SPI Communication ATmega328P 

It one of the best serial communication systems in the case of multiple peripherals. SPI protocol allows multiple devices to use the same channel for communication. It consists of four wires, two for data sending and one for clock but the fourth wire is used to select the peripherals knows as a select slave. In the case of multiple peripherals number of the select slave, pins will be increased. The SPI pins of the microcontroller are:

• MOSI – GPIO17
• MISO – GPIO18
• SS – GPIO16
• SCK – GPIO19

I²C Communication Module

Most of the peripherals come with the I²C communication method which is one way at a specific time. I²C protocol only uses one data wire and one clock wire. Data wire will transfer and receive the data and clock wire will send the clock pulse to keep the data sync. The wires on the microcontroller are:

• SDA – GPIO27
• SCL – GPIO28

TIMERS MODULES

ATtiny328P has two internal timers. We can use these timers to make counters and to generate pulses. Both of these timers are dependent on an oscillator. Both timers can use the internal and external clock to operate, but they also have an internal pin which can be used to count according to the external pulses. All of these pins in microcontroller ATmega328P are given below:

• T0 – GPIO6
• T1 – GPIO11
• TOSC1 – GPIO9
• TOSC2 – GPIO10
• ICP1 – GPIO

ICP1 is an input capture pin which can be used to capture the external pulse at a specific interval of time. When an input pulse will occur on this pin then it will generate a timestamp which can tell when the external signal was received.

SYSTEM CLOCK

The internal clock and external clock pulses can be divided by the Prescaler and their value can be received at an external pin. The external pin for divided clock pulses will be:

• CLKO – GPIO14

COMPARATOR MODULE

The microcontroller has internal comparator modules for analog signal. This module takes the input in inverting and non-inverting form which can be used further for any internal purpose or it can also be used to generate the output signals. Comparator pins of the microcontroller are listed below:

• AN0 (Positive) – GPIO12
• AN1 (Negative) – GPIO13

ATmega328P CAPTURE/COMPARE/PWM Channels 

There are six capture/compare/PWM pins are used to generate the desired time pulse-based signal. It uses a Prescaler to divide the time pulse. All of these pins in ATmega328P are:

• OC0B – GPIO11
• OC0A – GPIO12
• OC1A – GPIO15
• OC1B – GPIO16
• OC2A – GPIO17
• OC2B – GPIO5

ANALOG TO DIGITAL CONVERTER Channels

In ATmega328P there are 6 ADC channels that can be used to convert the analog signal to digital. The analog converter needs to be activated first by its power pin (AVCC). The ADC channels use power supply voltage as a reference to differentiate the different levels of the analog signal. The analog pins of the controller are:

• ADC0 – GPIO23
• ADC1 – GPIO24
• ADC2 – GPIO25
• ADC3 – GPIO26
• ADC4 – GPIO27
• ADC5 – GPIO28
• AVCC – Pin20

AREF PINS

Sometimes the analog signal voltages are fluctuating but it kept measuring by the controller according to the power input of the controller. To measure it by any other power input or by the power of analog signal generating device, an analog voltage reference AREF will be used. This pin will detect the maximum value of the analog signal and then it will be able to give the proper output. AREF pin in ATmega328P is:

• AREF – GPIO21

RESET: In ATmega328 there is some reset to restart the microcontroller in some conditions. In all of these resets there is an external reset to reset the device using an external signal:

• RESET – GPIO1

POWER: Every controller needs the power to operate and it always has a power input pin. In ATmega328P the power pins are three in number. One pin is for voltage and the remaining two are for common ground. Both of these ground pins are connected internally, it doesn’t matter which one is used. The power pins of the microcontroller are:

• VCC – Pin7
• GND – Pin8, Pin22

OSCILLATOR: The controller comes with 8MHz changeable oscillator. However, it can also use the external oscillator up to 40MHz. To use the external oscillator, oscillation pins will be required for input and output of the signal. Those pins are given below:

• XTAL1 – GPIO9
• XTAL2 – GPIO10

ATMEGA328P Block Diagram

The block diagram of the microcontroller ATmega328P is given below:

Pin Mapping of ATmega328P with Arduino 

ATmega328 comes in Arduino, which helps the users to code the program in Arduino instead of assembly or other controller languages. Arduino is popular because of its vast online data and high-level language, and this helps the developer to code the controller program in Arduino and them convert it into the microcontroller code. In case of Arduino the pin configuration for the controller will be the following:

In the case of Arduino, the pins become specific to their functionality. During using the compiler of ATmega328 almost all pins can be used as GPIO. However, during the usage of Arduino, each pin will perform the specific function only, but the controller will still be able to perform all the operations like ATmega328.

APPLICATIONS

• Most of the embedded systems like IoT based uses ATmega328 to perform multiple kinds of operations due to its vast examples and helping material on the internet.
• It is used in Arduino which makes it the most popular controller.

2D DIAGRAM